快速換模-SANDSUN 山田順精機

Clamp Selection | Introduction

CLAMP SELECTION

MODEL SELECTION

CBCB

CB-NCB-N

CB-CCB-C

CB-BCB-B

CB-SCB-S

CB-VRCB-VR

 

CB-①②

 ▼ ┗━━━━━━━━━━━━━━━━━━▼

 

①Capacity of clamp: 2-50 (tons) ②
  ●Empty: Standard type                                                 ●S: Slide moveable type
●N: Wiith sensor type/DC10~30V (NPN, 3-Wire)         ●V: Heat-resistant type
●C: Pneumatic cylinder movable type                        ●B: Fixed type
●VR: Heat-resistant with cover type
 

INSTRUCTION OF SPECIFICATION

Unit:mm

MODEL CB-2 CB-4 CB-6 CB-10 CB-16 CB-25 CB-50
Capacity of clmap/*tons
 2 4 6 10 16 25 50
Total stroke (X)/mm
 8 8 8 8 8 8 10
Stroke of clamp (Y)/mm
 3 3 3 3 3 3 4
Presserved stroke (Z)/mm
 5 5 5 5 5 5 6
Total volumn of cylinder/cc
 7.5 13 21 38 55 98 220

*Hydraulic pressure: 250kgf/cm²

 
INTRODUCTION

ModelCB


 

OUTLINE DIMENSIONS:

Unit: mm

MODEL L K J min. E F G min. C
CB-2
 110 90 20 73 68 32 10
CB-4
 134 110 24 77 79 40 12
CB-6
 159 130 29 92 96 46 14
CB-10
 189 159 30 114 117 54 16
CB-16
 230 200 30 126 129 58 20
CB-25
 265 235 30 148 156 70 23
CB-50
 320 290 30 180 246 110 34

The size of clampsA B Cand D are made based on the size of T-slot.

 

VERTICAL LOADINGPlaten with T-slot

 

Optional for position checking sensor

 

ModelCB-N


 

OUTLINE DIMENSIONS:

Unit: mm

MODEL A B min. E G J K L
CB-2N
 56 34 73 32 20 90 110
CB-4N
 61.5 39.5 77 40 24 110 134
CB-6N
 70 48 92 46 29 130 159
CB-10N
 80 58.5 114 54 30 159 189
CB-16N
 86 64.5 126 58 30 200 230
CB-25N
 99 78 148 70 30 235 265
CB-50N
 145 123 180 110 30 290 320
 

VERTICAL LOADINGPlaten with T-slot and manual clamp with sensor.

 

 

ModelCB-C


 

OUTLINE DIMENSIONS:

Unit: mm

MODEL A B C D E F G K L Rc Tapping(T)
CB-2C
 56 68 28 41 20 57.5 66 90 131 1/8 M6x12D
CB-4C
 61.5 73.5 28 46.5 20 57.5 71.5 110 131 1/8 M6x12D
CB-6C
 70 86 34 55 24 62.5 82 130 135 1/8 M6x12D
CB-10C
 80 104 40 66 30 48.5 101 159 129 1/8 M8x16D
CB-16C
 86 119.5 50 73.5 36 50 117 200 141 1/8 M10x20D
CB-25C
 99 133 50 87 36 50 130 235 141 1/8 M10x20D
CB-50C
 145 263 100 138 110 62 220 290 192 3/8 M16x32D
 

VERTICAL LOADINGPlaten with T-slot and clamps moved automatically by pneumatic cylinder.

Another selection of clamping direction: left-right.

 

ModelCB-S


 

OUTLINE DIMENSIONS:

Unit: mm

MODEL A B C D min.E F G W max. N Tapping (T)
CB-2S
 12 20 80 98 90 76 30 124 25 M10X20D
CB-4S
 12 25 100 109 93 87 30 135 30 M12X24D
CB-6S
 15 30 120 126 109 104 30 152 35 M12X24D
CB-10S
 15 35 150 148 131 124 36 174 40 M14X28D
CB-16S
 20 40 200 166 142 138 44 200 50 M18X36D
CB-25S
 20 50 235 200 163 168 48 240 60 M22X45D
 

VERTICAL LOADINGFor Platen without T-slot and the sizes of mold are variable.

 
SUGGESTED DIMENSION OF T-SLOT | ADDITIONAL T-SLOTS PLATEN

 

T: the thickness of additional T-slot platen (min.)

Unit: mm

MODEL T a b c d
CB-2
 32 18 32 14 18±0.2
CB-4
 40 22 37 16 24±0.2
CB-6
 40 22 37 16 24±0.2
CB-10
 44 28 48 18 26±0.2
CB-16
 52 28 48 22 30±0.2
CB-25
 61 36 56 25 36±0.2
CB-50
 84 48 80 36 48±0.2

 

ModelCB-B


 

OUTLINE DIMENSIONS:

Unit: mm

MODEL A B D F G min. E W Tapping (T)
CB-2B
 12 35 90 20 84 90 106 M10X20D
CB-4B
 12 40 110 25 95 93 117 M12X24D
CB-6B
 15 45 130 30 115 109 140 M12X24D
CB-10B
 15 55 159 30 135 131 160 M14X28D
CB-16B
 20 65 200 30 158 142 192 M16X32D
CB-25B
 20 80 235 30 184 163 218 M18X36D
 

VERTICAL LOADINGFor Platen without T-slot and the sizes of mold is unified.

Suggest CB-S for movable platen.

 

ModelCG

 

CG Clamp is charactered in mechanical locking system.
The holder of clamp can be shrunk into the clamp when unclamping. It can avoid interference between the holder and mold template.
It is only applied on Mold Changer System.

 

MODEL SELECTION

CG-①B-②-③-④

 

①The capacity of clamp (4~50 ton)
②Thickness of template (H±0.5mm)
③The direction of piping and wiring connection:
L: on the left side (as below drawing)
          R: on the rigt side
          U: on the upper side
④Sensor voltage:
3: DC10~30V (NPN, 3-Wire)
          4: DC10~30V (PNP, 3-Wire)

 

INSTRUCTION OF SPECIFICATION

Unit: mm

MODEL CG-4B CG-6B CG-10B CG-16B CG-25B CG-50B
Clamping force
 *tons 4 6 10 16 25 50
Retaining force
 **tons 0.8 1.2 2 3.2 5 10
Preserved stroke (Z)
 mm 1.5 2
Working temperature
 ℃ Max 70℃

* Hydraulic Pressure: 140kg/cm²
** No hydraulic pressure

 

CG-4B~10B11

 

CG-16B~50B11

Unit: mm

MODEL A B C D E F G I J K L M N O P Q Rc H±0.5 T
CG-4B
 186 123 75 50 30 113 42 17 2 27 90 62 35 14 - 115 1/4 25 M16
CG-6B
 202 140 85 48 36 126 48 19 3 33 110 76 45 17 - 124 1/4 30 M20
CG-10B
 215 150 98 53 42 138 56 23 3 36 135 95 50 20 - 131 1/4 30 M24
CG-16B
 258 190 128 74 53 175 82 28 5 33 138 104 60 17 40 156 1/4 30 M20
CG-25B
 302 240 159 100 64 212 100 33 5 40 170 130 75 20 50 188 1/4 40 M24
CG-50B
 365 290 195 140 88 268 125 35 5 50 215 162 100 27 60 227 3/8 50 M33

 

back to top
Introduction Clamp Selection | Introduction

Sandsun Precision Machinery Co., Ltd. | Chang-hwa, Taiwan, R.O.C. | Tel: 886-4-8536688 | Fax:886-4-8536699 | Sitemap